questions about - Keypad

Programming the Marantec M3-631 Keyless/Keypad

1. On the Marantec M3-631 Keypad, open the terminal area and using the programming connector, connect the keypad to a programmed handheld remote. 2. On the handheld remote, press and hold the transmitter button you use to open and close the 3. On the keypad press the “enter” button while still holding the handheld remote button down. The keypad backlight will come on. 4. While still holding the handheld remote button down, on the keypad enter the 4 digit code you wish to use and then press the “enter” button. 5. Continue to hold the handheld button down until the
read more→

Programming Linear MDTK Wireless Keypad
garage-door-wireless-keypad-linear-program

Locate the learn button on the back or side of the Linear Opener. Press the learn button on the Linear opener. The learn light will come on. On the Linear MDTK keypad enter a 1-6 digit code you want to use to open/close the garage door. The light on the opener will flash when the keypad code is learned/accepted. Testing the keypad, on the keypad enter the 1-6 digit code you chose and then press the start/stop button on the keypad. The door should open and close. Repeat the listed steps for each additional code for this keypad. The MDTK
read more→

Programming Genie GWK Wireless Keypad

The Genie Model GWK Wireless Keypad is for use with the older Genie openers with 9 or 12 DIP switches. To program this keypad you will need to note the location of the DIP switches on the opener motor. (The locations will be either up or down) The following list will help finding the code. You will have a 3 digit code for 9 DIP switches and a 4 digit code for 12 DIP switches. (You will use groups of 3 to determine the code) DIP Switch Position Codes Up-Up-Up =7 Up-Up-Down=6 Up-Down-Up=5 Up-Down-Down=4 Down-Up-Up=3 Down-Up-Down=2 Down-Down-Up=1 Down-Down-Down=0 First determine
read more→

Programming Genie Wireless Keypad Model GK-R/GK-BX
how-to-program-genie-wireless-keypad-GK-R

The Genie Model GK-BX (aka: GKCA-BX, GKCG-BX, GKCT-BX) wireless keypad can be programmed to work with 1-3 different garage doors. The following procedures will walk you through the programming process. You will first need to prepare the wireless keypad to work with any Genie Intellicode opener. This procedure is for programming a single garage door to the keypad. 1. On the keypad press 3-5-7 and then press the up/down key. 2. The keypad light should go to a solid lighted condition. 3. Press and hold the program key until the LED light changes from green to red. 4. Release the program key and allow
read more→

Programming Liftmaster 877MAX Wireless Keypad

The Liftmaster 877MAX is compatible with Garage Door Openers that operate on 315 MHZ or 390 MHZ that were manufactured after January 1, 1993. Your garage door opener will need to have a functioning lightbulb for program as the light is a programming indicator. Before you start you will need to locate the learn button on the operator motor. If you have problems locating the learn button refer to the user’s manual for your garage door opener. Programming Keypad: 1. On the keypad press and hold the # and * buttons until the keypad lights stop flashing. 2. Press and
read more→

Programming the Liftmaster 387LM Universal Wireless Keypad
how-to-program-liftmaster387-universal-wireless-keypad

To program the Liftmaster 387LM Universal Wireless Keypad you will first need to determine what brand garage door opener you have and if has DIP switches or a learn button for programming. 3 Position DIP Switches (Chamberlain, Craftsman, Liftmaster, Master Mechanic and Do It openers) 1. Choose a 4 digit PIN 2. Determine your garage door opener ID  ID DIP Switch Type  11= 9 DIP switch made in USA  12= 9 DIP switch made in Canada  15= 8 DIP switch  19=7 DIP switch 3. On the opener and remote the first DIP switch must be
read more→

Programming Wayne Dalton Remotes and Keypads
wayne-dalton-openers.jpg

Instructions for programming Wayne Dalton keypads and remotes This content was already uploaded to the website without editing it.   First it will be much easier to program the keyless entry in your hand before it is mounted to a wall but is not necessary. Also you will have to make sure that the opener is in the down position so that the door is fully closed before starting the programming process.     Locate the learn button it is on the right side of the opener towards the back of the motor head and it is labeled program button and it has
read more→